Recent content by Brushless FPV Junkie

How is everyone feeling about the actual performance of the rpm filtering? I expected more. I know the esc firmware is in beta but it works so I know the fc has the proper bidirectional dshot telemetry. I suppose I can't expect too much considering my 6S 7inch builds have required a little...

Anyone out there using the RPM filters and Bidirectional dshot telemetry test firmware on 7inch builds without the need for any additional Gyro Filtering? I have betaflight 4.0.2 and Blheli32's Bidirectional dshot telemetry firmware installed on both of my 6S 7inch LR builds. I have things...

Anyone out there built a 7 inch 6S they had success with? V1 flies well except a little gyro noise the SW LP and notch filters in BF 3.5.7 won't get grid of. I think the Aikon F4 I'm using would be better for a 5inch. I really hope the Bosch Gyro in this raddix I bought for V2 yields better results.

I have high Hope's for the Brain fpv raddix and the 2506 1250kv motors I bought for V2. It will use the same 300mm stretched X frame as V1, same Akk infinite DVR LR edition VTX and same Runcam swift 2 as well. Just waiting on the frame, Gemfan 7056 props and the hobbywing Xrotor blheli32 45amp...

The 7inch 6S prototype V1 is my favorite acro quad I've built so far. V2 will be even better I hope. Just waiting on a frame and esc to be delivered.

Still waiting on esc and frame for v2.

This is the 7inch prototype. This is the 7inch 6S prototype V1.

It's probably worth saying. It's fast, very. Handles far better than expected. The Bosch gyro on the brain fpv raddix I'm buying should help improve upon the low throttle gyro noise issue I'm currently unable to filter on V1. V2 will surely benefit from arguably the best gyro for the noise...

My 6S 7inch prototype is fast and handles better than expected. V2 is underway.

I built my prototype. It actually flies better than I had imagined despite some gyro noise I've had difficulty filtering. The prototype battery is much smaller in capacity and weight than I intend to use for the final version. However the form factor and weight distribution has a perfect cg...

7 inch Long range prototype in progress

The Idea: 7 Inch hq 7×3.5 V1S 360mm streched X frame 2207 1700kv motors Lumineer 50amp 4in1 esc Dshot 1200 esc protocol F7 Kakute FC (soft mounted) Betaflight 3.5.6 or 4.0 if released 6S 1500mah 75c Runcam swift 2 2w (2000mw) 2.4ghz vtx 900mhz 2w crossfire TX & RX It's a long range...

Bought a runcam Swift 2 and a new reciver so I would have better picture and be able to use SBus instead of ppm rx protocol as well as save some weight. Great picture + osd and this new reciver is so small. It's like the size of my index fingernail! So tiny! Eliminated every bit of 20grams with...

So most of my builds have been on knockoff "Lumineer" QAV-R frames. I have gotten used to flying x220 frames. I noticed Carlos, (Charpu) frequently or apparently consistently flies a Lumineer QAV 250 (HX style) frame. The weather is getting cold here in the Ohio, Kentucky, Indiana tri-state area...

Discovered F4 Omnibus FC. My F3 boards are soooo obsolete and I never knew until I saw the future. Thanks for the OSD advice everyone. It lead me to a far better way of doing things! Upgrading my quads to F4 FC's now and using blackbox for tuning. I love seeing my FC's inner most thoughts and...